Indiana/Major roads/Main: Difference between revisions Discussion View history

(*/Major_roads/Main*/)
(replaced lock standard table with template)
 
(10 intermediate revisions by 3 users not shown)
Line 1: Line 1:
<!-- This page is only transcluded into (displayed on) the main page for this state. See more detailed instructions below. --><noinclude>{{:USA/CommonState/ReturnPurge|{{SubPage2}}}}<br/></noinclude><!--
<!-- This page is only transcluded into (displayed on) the main page for this state. See more detailed instructions below. --><noinclude>{{:USA/CommonState/ReturnPurge|{{SubPage2}}}}<br/></noinclude><!--
------ DO NOT MODIFY ABOVE THIS LINE -------- DO NOT MODIFY ABOVE THIS LINE ------>  
------ DO NOT MODIFY ABOVE THIS LINE -------- DO NOT MODIFY ABOVE THIS LINE ------>  
 
=== State Route Naming ===
== Lock Levels ==
State highways that are primarily signed at entering intersections with a State Route number like [[image:75px-WV-2.svg.png|30px]] rather than a road name should be named IN-### ("IN-2").
 
 
Indiana currently observes the following Great Lakes Region minimum lock levels for Waze road types:
== Locking standard ==
 
{{Lock Standard State|IN}}
{{Freeway}} - '''5'''<br />
{{Major Highway}} (MH) - '''3'''<br />
{{Minor Highway}} (mH) - '''3'''<br />
{{Primary Street}} (PS) - '''2'''<br />
 
The {{Ramp}} road type is to be locked at the level of road it serves.<br />
:'''i.e.''' a ramp connected to a Freeway is locked at '''5''', a ramp serving a Major Highway, or Minor Highway intersection is locked at '''3''', etc.
 
{{Street}} All others - '''1'''
 
'''''Note:''' These are minimums and, for protection, certain segments may be at higher lock levels.''
 
 
== Name Normalization ==
 
Indiana will use the following standards for naming: <br>
Interstate System - I-xx <br>
US Highways - US-xx <br>
State Highways - IN-xxx <br>
County Highways - CR-xxx <br>
 
 
<!---- DO NOT MODIFY BELOW ------ DO NOT MODIFY BELOW ------ DO NOT MODIFY BELOW ----
<!---- DO NOT MODIFY BELOW ------ DO NOT MODIFY BELOW ------ DO NOT MODIFY BELOW ----
-------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------

Latest revision as of 20:01, 24 December 2018


State Route Naming

State highways that are primarily signed at entering intersections with a State Route number like rather than a road name should be named IN-### ("IN-2").

Locking standard

The following defines a set of minimum locking standards proposed for all roads within Indiana. Any road of a certain type or category must be locked at least to the level in the chart below. Roads may be locked higher for protection and special situations (tricky design, frequent mistakes, imaging inaccuracies, and the like), but should not be locked lower.

It is understood that more rural or inactive areas may not yet meet this standard: editors are encouraged to recruit and mentor additional editors to build coverage.

A great time to implement these locks is while bringing the road types of an area into compliance with the current US road type standards (FC and highway systems). Lock the roads based on type after they've been set to current US Road Type Standards.

Indiana Minimum Road Locking Standard
Segment Type Two-way   One-way 
 Freeway  5
 Ramp  Highest lock of connected segment
 Major Highway  3
 Minor Highway  3
 Primary Street  2 3
 Street  1 2
 Private Road  1 2
 Parking Lot Road  1 1see note
 • • • • Ferry • • • •   5
 |-|-|-|-|-|-|-|-|-| Railroad |-|-|-|-|-|-|-|-|-|  2
 ⁃     ⁃        ⁃        ⁃        ⁃ Runway ⁃        ⁃        ⁃        ⁃        ⁃  5
Other named types 1 2
Construction (outdated imagery) 3
Waze Beacons installed 6

Note: One-way PLRs used outside of parking lots, such as alleys and streets through apartment complexes, should be locked at 2. See the GLR major roads page for additional information on the standards listed here.