When mapping Railroad/Light Rail tracks, please keep the following information in mind (from the Railroad wiki page):
Use the following guidelines when mapping railroad segments:
If you do not know the owner of the railroad tracks, enter "Railroad" for the street name of every railroad segment.
Always select "None" for the city name. This avoids city smudging.
Lock the segment at L2.
Do not map railroads below ground, as they do not serve any of the three purposes outlined above. This is especially true in urban areas where underground rail lines are common, and their appearance on the map would be confusing to drivers.
Set the elevation just as you would a drivable segment. When tracks junction a road on the ground, the Elevation should be set to Ground.
Create junctions between drivable roads and railroads.[rr]
Set railroad to 2-way directionality
Restrict turns to and from the railroad segments.
When mapping railroad tracks, focus on those near drivable roads.
Map rail yards simply, with one railroad segment along either edge of the yard's tracks.
Map industrial spurs only if they cross drivable roads.
Do not map every piece of parallel track, such as in sidings or yards, or industrial spurs that don't cross any roads. Your work may otherwise be seen as clutter, much like mapping every parking lot row.
Multiple parallel lines at crossings:
At most crossings, there should be only one railroad segment mapped and no more than two parallel railroads mapped at any crossing.
Parallel lines are to be at least 5m apart
In general, there is no reason to have multiple lines mapped. When not at a crossing, even four parallel lines can be easily mapped as a single railroad segment in Waze.
Keep segment lengths under 10,000 meters – the longer the segment length, the more sluggish the editor is to respond to changes.
Do not map railroads using a drivable road type (streets, primary streets, etc.); it could be a hazard to human life if drivers were routed to them.
^rrNote: The routing server will properly account for delays at railroad crossings through a segment without a junction. However, with a junction, the historical data for the rail crossing will be more accurate.
Walking Trails
They should only be used in rare cases. Walking Trails may have strange side effects on nearby routing. Never use the Walking Trail road type for ordinary hiking paths or bike paths. Most hiking and bicycling paths should not be on the map at all.
The WME lists the Walking Trail road type as non-drivable. Historically, editors have disconnected Walking Trails to make sure Waze doesn't route drivers over them. This doesn't always work as desired. If a disconnected Walking Trail comes closer to a destination than any other road, Waze may route drivers to a location nearer to the Walking Trail than to the destination. This problem can be severe for Walking Trails passing close to many destinations in a dense neighborhood. Connected or not, the Walking Trail type should never be used where effects on local routing are not desired.
Dirt Roads 4x4
Utah follows the following functional classification for Gravel and Dirt Road /4x4 trails.
Gravel Roads
Functional Classification
Minor Arterial Minor Highway
Minor Collector Primary Street
Local/Not Mapped Street
Off-road / Not maintained
Functional Classification
Minor Arterial Off-road / Not maintained
Minor Collector Off-road / Not maintained
Local/Not Mapped Off-road / Not maintained
Images demonstrated above can not cover all scenarios for mapping maintenance level to Waze road type. These types of roads may undergo variation in quality over seasons additionally depending on the climate (rain/snow). Particularly, some gravel roads may have qualities that are closer to Dirt Road / 4x4 Trail than street. Editors with local experience or potential Street View images may help in this determination.
Driveways / Private Roads
Please follow the following guidelines for Private Driveways. Wiki standard can be found here. Driveways
Mapping rural diveways
If an address/location cannot be reasonably guided to without a private drive, it can be added.
Single house at the end of a 1mi (1609m) private drive, and that's the only house, it probably isn't needed.
If it's 5 houses at the end of a single shared 1/4mi (402m) long private drive, it probably is needed.
If it's a house at the end of a 500m (1640 ft) long private drive which is right up against another street from which you cannot access the address (stop point will be on the segment closest), then a private drive is probably needed.
