 |
Na stránke sa usilovne pracuje! |
Trajekty sú veľké lode na prepravu áut (a tiež ľudí) z nejakého prístavu do iného. Na Slovensku sú známe ako prievozy aklebo kompy. Trajekty obyčajne majú svoj vlastný plavebný poriadok a obvykle sú súčasťou dopravného systému.
V niektorých krajinách sú trajekty nevyhnutnou súčasťou cestného systému. Na niektorých územiach je potrebné ich mať zaznamenané na mape, pretože sú občas najlepším spôsobom a v niektorých prípadoch jediným možným spôsobom, ako sa dostať do cieľa.
Ale nie všetky trajekty musia byť mapované. Nasledujúce podmienky môžu byť rozhodujúce, keď sa rozhodujete pridať trajekt do mapy.
Kedy pridať a kedy nie
Trajekty, ktoré spĺňajú niektorú z týchto podmienok, by vo všeobecnosti nemali byť mapované:
- Osobné trajekty bez prepravy áut
- Trajekty potrebujúce prekládku (prestupovanie)
- Súkromné trajekty pre neverejné používanie
- Trajekty s plavbou dlhšou ako 2 hodiny
Ak trajekt nespĺňa žiadnu z týchto podmienok môže byť pridaný do mapy.
Ak máte pochybnosti o tom, či trajekt má byť zamapovaný, alebo nie, napíšte svoj dopyt na editorské diskusné fórum [1].
How to add
The full length of the ferry route and both docking points must be part of your editable area. It may be necessary to ride the ferry with Waze running to add that route to your area.
- Turn on the GPS Points Layer to see the ferry's typical path. If no GPS point are visible, it may be OK to simply draw a straight line between the two docks.
- Draw a segment from one ferry dock to the other following the GPS points. Name and label the new segment with No City and with the road name of the ferry line. This is often the combined names of both sides of the Ferry. For example: Bainbridge Island - Seattle Ferry. The road type should match the road type on either side of ferry. Do not use Ferry, Freeway, Parking Lot, or Private Road Types. If the ferry is a part of the highway system, then it should be marked Minor or Major Highway. Be sure to set the time restrictions on the segment including the first ferry (opening time) and the last ferry (closing time).
- Draw segments on both loading ramps using the same road type as the ferry. These should have the correct city name entered on each side and "Ferry Loading Ramp" in road name field for both. (Editor Note: This gives some separation from the ferry and the ferry's slow waiting lines, enabling better routing.)
- Draw a one-way segment connecting the loading ramp segment to the main road on both sides using the same road type as the ferry. Label it with the correct city name on each side and No Name in name field. If ferry has multiple exit routes and clear signs then you can label the exit road with the standard "to: X" and "to: Y". Example "to: Seattle" and "to: I-90 / I-5".
- Draw another one-way segment connecting the main roads to the loading ramp segment on both sides using the same road type as the ferry. Mark is as a toll road if it has a fee in the direction of this segment. It should be labeled with correct city name on each side and "to Bainbridge Island - Seattle Ferry". (Editor Note: some ferries charge riders going one direction and not the other. You commonly see this when ferries are going to an Island where the ferry is the only access, then the ferry going to the island is toll road and ferry going to main land is not tolled. Splitting exit and entrance ramps enable this flexibility).
Examples of properly mapped ferry docks
Road types
 |
The Ferry Road type is not to be used at this time. Do not use the Ferry Road type for any purpose. For more information see this forum for the latest information on this topic. |
Future ferry support
As of Feb 2014, there is no set schedule when Waze will add further support for ferry routes, but it is in the list of future features. See the talk page for more information.
