Vermont/Major roads/Main

Highway Numbering

Vermont currently observes the following Standardized Name nomenclature for Numbered Routes:

Road Type	Standardized Name
Freeways	I-###
US Highways	US-###
State Highways	VT-###

State Highway numbering includes spurs and loops (E.g. VT-67A).

These naming conventions should also be applied to "Old" numbered routes that have become local streets after the completion of new highway alignments. For example, "Old State Rte ##" and "Old US Hwy ##" Should be renamed "Old VT-##" and "Old US-##" respectively. In some cases, it may be necessary to research whether the old route was formerly a state or US highway.

State Highway Signage

Most state highways are maintained by the Vermont Agency of Transportation (VTrans). However, some entire routes, and portions of others, are maintained by local governments, such as towns or cities, instead. These town-maintained routes are internally called "state-designated town highways" and are typically designated as "class 1 town highways".

VTrans uses a different type of signage for each:
Vermont State Route signage (maintained by VTrans)
Vermont State Route signage (maintained by local jurisdiction)

Map editors should treat both types of state highways the same when dealing with road types.

Road Elevations

These are the general guidelines for elevation in Vermont. Note that these guidelines are currently under revision on the National level, and are subject to change:

• Drivable and non-drivable segments are handled the same way with elevation.
• Set elevation to Ground on all non-tunneled segments that are not passing over/beneath another segment or waterway.
• Only segments that "cannot see the sky" should have negative elevation (i.e. tunnels).
• Only set elevation as high as necessary.
  • Elevation of overlapping segments should be set relative to each other, with the lowest segment as Ground (unless a tunnel).
• If you use the Bridge tool to join segments, be aware that it raises the elevation of the joined segment. Lower the joined segment as appropriate.

Highway Naming

See Road names/USA and Road types/USA for general guidelines for naming and classifying roads.

Regarding Local and Alternate Names:

In situations where a highway passes through a town, the road in those areas is typically named something other than the numbered route. In these situations the road should be named based on the following conditions:

• If the local street signs provide guidance with the local name, that should be used as the primary name in the Waze map. The numbered route should be added as an alternate name.
• If the local signs only indicate the route number, then that should be the primary name and the local road name should be added as an alternate name.

Locking roads

In Vermont we have a set minimum standard for locking roads based on segment type. Any road of a certain segment type must be locked at least to the rank (level) in the chart below. Roads may be locked higher for protection and special situations (areas with construction, tricky design, frequent mistakes, imaging inaccuracies, and the like), but should not be locked lower.

A great time to implement these locks is while bringing the road types of an area into compliance with the current US road type standards (FC and highway systems). Lock the roads based on type after they've been set to current US road type standards.

Vermont Minimum Locking Rank Standard

Segment Type	Statewide
Freeway	5
Ramp	Highest rank of connected segments
Major Highway	4
Minor Highway	3
Primary Street	1 (Auto)
Street	1 (Auto)
Private Road	1 (Auto)
• • • • Ferry • • • •	5
|-|-|-|-|-|-|-|-|-| Railroad |-|-|-|-|-|-|-|-|-|	2

Note: Do Not Mass Edit just to update locks to these standards, these can be adjusted as you find them while editing other aspects of the segments such as FC, speed limits, naming, etc.

Some segments still warrant higher locks and care should be taken when setting segment lock to these standards to look for and protect these special setups with higher locks. Some examples; segments which are part of BDP, U-turn prevention, or using micro-doglegs, or other complex intersection setups.

Functional Classification

Functional Classification updates in Vermont have been completed. This will ensure a consistent, and better navigational experience to Wazers around the state and country. The general guidelines for implementation are in the Road Types (USA) page. Any local deviations, and special information for Vermont will be listed below.

Resources

Vermont's Agency of transportation (VTRANS) has made a master Functional Classification map available online, in PDF format.

• 2013 Functional Classification Map
• Vermont Roads FC Shapefile - 2003

VTRANS GIS class and color description

GIS Legend

The Vermont Classification and Color scheme comes from the official Functional Classification (FC) map that is published by VTRANS. The legend shows what classifications VTRANS uses and what color is assigned to each class.

VTrans to Waze Conversion Table

The numbers correspond to the FC type indicated on some VT maps. (e.g. Functional Class 7 road is a Major Collector)

		Highway Systems
		Interstate	US Hwy (incl. some special routes)	US Hwy BUS, SPUR, LOOP	State Hwy (incl. some special routes)	State Hwy BUS, SPUR, LOOP	Locally-maintained
	example>>>>>	I-95 N	US-2	US-460 Business	SR-27 (SR-27A)	SR-400 Loop	Robertson St
F u n c t i o n a l C l a s s	Principal Arterial Interstate (1,11)	Fw	n/a	n/a	n/a	n/a	n/a
	Principal Arterial - Freeway (12)	n/a	Fw	Fw	Fw	Fw	Fw
	Principal Arterial (2,14)	n/a	Major	Major	Major	Major	Major
	Minor Arterial (6,16)	n/a	Major	Minor	Minor	Minor	Minor
	Major Collector (7,17)	n/a	Major	Minor	Minor	PS	PS
	Minor Collector (8)	n/a	Major	Minor	Minor	PS	PS
	Local Road (9,19)	n/a	Major	Minor	Minor	PS	Street